IoT cloud for ESP32, Arduino and Pi

Your projects, looked after.
Even while you sleep.

Connect an ESP32, Arduino or Raspberry Pi and build automations that act for you and message you on Telegram, Discord or email.

Free for good. Every feature, no card needed.

An automation, playing out

One cold night, five steps.

The greenhouse drops below 2 °C at 2:42 am. Here's what WBSKT does while you sleep.

Greenhouse3:07 am

It was below 2 °C for 10 minutes, so I switched the heater on. It's 3.4 °C now.

A run of the Frost alert ruleFrost alert, in the console

Reliable automations

It doesn't lose its place.

Each step is saved as it runs. A failed step tries again, a restart picks up where it stopped, and every run is kept.

Wi‑Fi drops

Your board reconnects and carries on. The rule runs on WBSKT, so it was never waiting on your board.

Failed steps try again

A step that fails is retried, and a restart resumes the run at the step it stopped on.

30 days of readings

Hourly charts go back a month on Free and up to two years on a paid plan, so you can look back at last week's cold snap.

How it works

Three small steps. Most people are done in about ten minutes.

01

Connect your board

Add a few lines to your sketch. Your board joins Wi‑Fi and starts sending readings.

02

Build an automation

Pick what to watch and what should happen, like "below 2 °C, turn the heater on". No code, just choices in a visual builder.

03

Get on with your day

WBSKT sends you a message, switches something on, or both. You only hear from it when it matters.

Libraries for Arduino, ESP32, Python and .NET

Add your key and your Wi‑Fi, then send whatever your sensor measures. Already use MQTT? Any MQTT library works too, with no broker to run.

Arduino & ESP32betaRaspberry Pibeta.NETbeta

In beta. All three libraries are out as 0.9 betas, and the protocol may still change before 1.0. Compare the libraries

Copy
#include <WiFi.h>
#include <Wbskt.h>

WbsktClient wbskt("greenhouse-sensor", "your-policy-pin");

void setup() {
  WiFi.begin("home-wifi", "wifi-password");
  wbskt.begin();
}

void loop() {
  wbskt.loop();
  static unsigned long last = 0;
  if (millis() - last < 60000) return;
  last = millis();
  JsonDocument reading;
  reading["celsius"] = readTemperature();
  wbskt.send("temperature", reading);
}
using Wbskt;

await using var wbskt = new WbsktClient("greenhouse-sensor", "your-policy-pin");
await wbskt.StartAsync();

while (true)
{
    await wbskt.SendAsync("temperature", new { celsius = ReadTemperature() });
    await Task.Delay(TimeSpan.FromMinutes(1));
}
import time
from wbskt import WbsktClient

client = WbsktClient("greenhouse-sensor", policy_pin="your-policy-pin")
client.start()

while True:
    client.send("temperature", {"celsius": read_temperature()})
    time.sleep(60)

Project ideas for ESP32 and Arduino

Small projects that are nice to have running in the background.

Frost alert

When the greenhouse stays below 2 °C for 10 minutes, turn the heater on, check again in 15 minutes and message me.

Garage left open

When the door is still open after 10 pm, close it. If it doesn't report closed within a minute, message me.

Thirsty plants

When the soil has been dry for an hour, run the pump for 20 seconds. Still dry 10 minutes later? Message me.

Print finished

When the 3D printer goes quiet, send an email.

WBSKT vs Arduino Cloud, Blynk and Adafruit IO

The platforms makers usually weigh up, side by side. We're ahead on rules and behind on a few things we're still building.

FeatureWBSKTArduino CloudBlynkAdafruit IO
Free plan20 boards2 devices5 devices10 feeds
First paid plan$50 a year$72 a year$415 a month$99 a year
Rules that wait for a reading to lastYesNoPartlyNo
Several steps, waits and branchesYesNoBasicBasic
Commands with delivery receiptsYesSynced variablesVirtual pinsNo
Arduino and ESP32 libraryBetaYesYesYes
ChartsComing soonYesYesYes
Phone appNoYesYesWeb only

Checked in October 2026 against each platform's public pricing and docs; Blynk's prices are from May 2026. Plans change, so check before you choose.

Free to start, about 5 cents a board as you grow

Every plan has every feature. Plans differ only in how many boards you connect, how much they send and how long readings are kept.

Free$0For good, no card needed
  • 20 boards
  • 1.5M messages a month
  • 2,000 workflow credits a month
  • 3 days raw, 30 days hourly
  • 1 workspace, 1 member
MakerFor most makers$5/ monthor $50 a year, 2 months free
  • 100 boards
  • 10M messages a month
  • 25,000 workflow credits a month
  • 7 days raw, 1 year hourly
  • 3 workspaces, 3 members
Pro$24/ monthor $240 a year, 2 months free
  • 500 boards
  • 50M messages a month
  • 150,000 workflow credits a month
  • 7 days raw, 2 years hourly
  • 10 workspaces, 10 members
Team$99/ monthor $990 a year, 2 months free
  • 2,000 boards
  • 200M messages a month
  • 600,000 workflow credits a month
  • 7 days raw, 2 years hourly
  • 25 workspaces, 25 members
Business$0.15a board a monthFrom 2,000 boards ($300 a month), on a yearly contract paid by invoice
  • 90 days of raw readings and run history
  • Never slowed: extra traffic is billed at contract rates
  • 50 workspaces, 50 members
  • Sized by contract to your fleet
  • Never a surprise bill. On Free, Maker, Pro and Team, reaching a limit slows or pauses things. It never charges you.
  • Busy month? 10,000 extra workflow credits cost $5 on any plan and last 12 months.
  • Paid plans open soon. Until they do, everyone is on Free.